Product ITEM is unavailable. See products from the same category below.
Retaining-Ring Pliers & Sets
Retaining-ring pliers install and remove snap rings that fit into a bore or onto a shaft and hold components in place. Also known as circlip pliers, their tips provide a firm grip on the rings to prevent them from flying off. Each pair of pliers adjusts its jaws to accommodate rings within a set diameter range. Retaining-ring pliers are commonly used to place rings on actuators, gear assemblies, motor shafts, and other machinery.
Designed to install or remove circlips and retaining rings such as the Anderton N1300, 1302 and 1308: Industrial 3000 and 4000: and Truarc N5000, 5002 and 5008. These snap ring pliers are convertible, comes with fixed a 0.090-inch tip angled at 90 degrees, and have an overall length of 9 1/4 inches. The bore diameter has a size range of 1.1812 to two inches and 2.062 to three inches.
Designed to install or remove circlips and retaining rings such as the Anderton N1300, 1302 and 1308: Industrial 3000 and 4000: and Truarc N5000, 5002 and 5008. These snap ring pliers are convertible, comes with fixed a 0.090-inch tip angled at 90 degrees, and have an overall length of 9 1/4 inches. The bore diameter has a size range of 1.1812 to two inches and 2.062 to three inches.
Designed to install or remove circlips and retaining rings, these internal snap ring pliers have replaceable tips, an overall length of 7 1/2 inches with a bore diameter of 3/8 inch.
Designed to install or remove circlips and retaining rings, these internal snap ring pliers have replaceable tips, an overall length of 7 1/2 inches with a bore diameter of 3/8 inch.
Made for installing or removing circlips and retaining rings, these industrial external snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 038-inch tips, a shaft diameter of 0.125 to one inch, and an overall length of 6 1/4 inches.
Made for installing or removing circlips and retaining rings, these industrial external snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 038-inch tips, a shaft diameter of 0.125 to one inch, and an overall length of 6 1/4 inches.
Built to install or remove circlips and retaining rings, these six-inch industrial snap ring pliers are convertible and come with a 0.047-inch tip angled at 18 degrees. The bore diameter has a size range of 5/16 to 3/8 inches.
Built to install or remove circlips and retaining rings, these six-inch industrial snap ring pliers are convertible and come with a 0.047-inch tip angled at 18 degrees. The bore diameter has a size range of 5/16 to 3/8 inches.
Built to install or remove circlips and retaining rings such as the Anderton N1308, Industrial 4000, and Truarc 5008. These snap ring pliers are convertible, comes with fixed a 0.047-inch tip angled at 90 degrees, and have an overall length of six inches. The bore diameter ranges from 1.06 to 1.375 inches.
Built to install or remove circlips and retaining rings such as the Anderton N1308, Industrial 4000, and Truarc 5008. These snap ring pliers are convertible, comes with fixed a 0.047-inch tip angled at 90 degrees, and have an overall length of six inches. The bore diameter ranges from 1.06 to 1.375 inches.
This replacement tip kit is built to fit heavy-duty retaining ring pliers B112 and B113. These tips are 0.120 inches in size with a variety of angles including straight, 15 degrees, 45 degrees, and 90 degrees.
This replacement tip kit is built to fit heavy-duty retaining ring pliers B112 and B113. These tips are 0.120 inches in size with a variety of angles including straight, 15 degrees, 45 degrees, and 90 degrees.
Recommended for automotive applications including ignition, distributor and spark plug terminals. Strip and crimp insulated wires with an 18, 16, 14, 12, and 10 gauge, or non-insulated connections seven- or eight-millimetre gauge. This heavy-duty multi-purpose plier has a total length of 9 3/4 inches.
Recommended for automotive applications including ignition, distributor and spark plug terminals. Strip and crimp insulated wires with an 18, 16, 14, 12, and 10 gauge, or non-insulated connections seven- or eight-millimetre gauge. This heavy-duty multi-purpose plier has a total length of 9 3/4 inches.
Designed to install or remove circlips and retaining rings such as the Anderton 1408, Industrial 4100, and Truarc 5108. These snap ring pliers are convertible, come with fixed a 0.090-inch tip angled at 45 degrees and have an overall length of 9 1/4 inches. The shaft diameter ranges from 2.156 to 3.25 inches.
Designed to install or remove circlips and retaining rings such as the Anderton 1408, Industrial 4100, and Truarc 5108. These snap ring pliers are convertible, come with fixed a 0.090-inch tip angled at 45 degrees and have an overall length of 9 1/4 inches. The shaft diameter ranges from 2.156 to 3.25 inches.
Built to install or remove circlips and retaining rings, these snap ring pliers are convertible, comes with fixed a 0.070-inch tip angled at 90 degrees and have an overall length of seven inches. The bore diameter ranges from 1 1/16 to two inches.
Built to install or remove circlips and retaining rings, these snap ring pliers are convertible, comes with fixed a 0.070-inch tip angled at 90 degrees and have an overall length of seven inches. The bore diameter ranges from 1 1/16 to two inches.
Designed to install or remove circlips and retaining rings, these industrial internal snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 0.090-inch tips, bore diameter of 1.812 to 3.5 inches, and an overall length of nine inches.
Designed to install or remove circlips and retaining rings, these industrial internal snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 0.090-inch tips, bore diameter of 1.812 to 3.5 inches, and an overall length of nine inches.
Designed to install or remove circlips and retaining rings, these external snap ring pliers have replaceable tips, an overall length of 7 1/2 inches with a bore diameter of 1/4 inch.
Designed to install or remove circlips and retaining rings, these external snap ring pliers have replaceable tips, an overall length of 7 1/2 inches with a bore diameter of 1/4 inch.
Designed to install or remove circlips and retaining rings, these heavy-duty internal snap ring pliers have a spring ratchet lock assembly, an overall length of 9 1/2 inches with a shaft diameter of 2 7/16, and a bore diameter of four inches.
Designed to install or remove circlips and retaining rings, these heavy-duty internal snap ring pliers have a spring ratchet lock assembly, an overall length of 9 1/2 inches with a shaft diameter of 2 7/16, and a bore diameter of four inches.
Built to install or remove circlips and retaining rings, these industrial internal snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 0.038-inch tips, a shaft diameter of 0.375 to 1.023 inches, and an overall length of 5 1/2 inches.
Built to install or remove circlips and retaining rings, these industrial internal snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 0.038-inch tips, a shaft diameter of 0.375 to 1.023 inches, and an overall length of 5 1/2 inches.
Made for installing or removing circlips and retaining rings, these industrial internal snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 0.070-inch tips, bore diameters of 1.062 to 1.750 inches and 1.437 to two inches, and an overall length of 6 1/2 inches.
Made for installing or removing circlips and retaining rings, these industrial internal snap ring pliers have fixed tips and vinyl grips. These pliers have straight-angled, 0.070-inch tips, bore diameters of 1.062 to 1.750 inches and 1.437 to two inches, and an overall length of 6 1/2 inches.
Built to install or remove circlips and retaining rings, these six-inch industrial, external snap ring pliers come with vinyl grips and a fixed 0.038-inch tip angled at 90 degrees. The bore diameter has a size range of 0.125 to one inch.
Built to install or remove circlips and retaining rings, these six-inch industrial, external snap ring pliers come with vinyl grips and a fixed 0.038-inch tip angled at 90 degrees. The bore diameter has a size range of 0.125 to one inch.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
