Adhesive & Sealant Surface Preparation

This SF 7452 accelerator is clear and comes in a 0.7 fluid ounce aerosol can. It meets the standards for MIL-A-46050C. This accelerator features instant cure.

This SF 7452 accelerator is clear and comes in a 0.7 fluid ounce aerosol can. It meets the standards for MIL-A-46050C. This accelerator features instant cure.

This SF 712 accelerator is clear and comes in a 1.75 fluid ounce bottle. It meets the standards for CFIA and MIL-A-46050C.

This SF 712 accelerator is clear and comes in a 1.75 fluid ounce bottle. It meets the standards for CFIA and MIL-A-46050C.

This SF 7387 activator is yellow and comes in a 1.75 fluid ounce bottle. It meets the standards for OSHA Hazard Communication Standard (29 CFR 1910.1200). This activator features speed up curing of most Loctite acrylic adhesives.

This SF 7387 activator is yellow and comes in a 1.75 fluid ounce bottle. It meets the standards for OSHA Hazard Communication Standard (29 CFR 1910.1200). This activator features speed up curing of most Loctite acrylic adhesives.

This Frekote PMC cleaner is clear and comes in a one gallon container. This cleaner features also cleans epoxy and metal mould surfaces, dissolves and removes wax from polyester moulds, no surface dulling.

This Frekote PMC cleaner is clear and comes in a one gallon container. This cleaner features also cleans epoxy and metal mould surfaces, dissolves and removes wax from polyester moulds, no surface dulling.

This SF 7113 accelerator is clear and comes in a 1.75 fluid ounce bottle. It meets the standards for OSHA Hazard Communication Standard (29 CFR 1910.1200).

This SF 7113 accelerator is clear and comes in a 1.75 fluid ounce bottle. It meets the standards for OSHA Hazard Communication Standard (29 CFR 1910.1200).

This PU 8519 P primer and activator is black and comes in a 100 mL bottle. This primer and activator features activation of cut beads (after more than two hours open), adhesion promotion, corrosion prevention, evapouration time is approximately two minutes, even in cold environment for two-component direct glazing products 15 m.

This PU 8519 P primer and activator is black and comes in a 100 mL bottle. This primer and activator features activation of cut beads (after more than two hours open), adhesion promotion, corrosion prevention, evapouration time is approximately two minutes, even in cold environment for two-component direct glazing products 15 m.

This SF 7452 accelerator is amber and comes in a one quart can. Adhesive and sealant accelerators increase an adhesive's cure speed to quickly bond materials. These accelerators work with instant adhesives and large, gap-filling applications where there isn't enough moisture present to cure sealant on its own.

This SF 7452 accelerator is amber and comes in a one quart can. Adhesive and sealant accelerators increase an adhesive's cure speed to quickly bond materials. These accelerators work with instant adhesives and large, gap-filling applications where there isn't enough moisture present to cure sealant on its own.

This SF 7090 activator is blue and comes in a one ounce bottle. This activator features also recommended for large gaps, low viscosity, solvent-free, suitable where prevailing temperatures are as low as less than+59 Degrees f (less than+15 Degrees c).

This SF 7090 activator is blue and comes in a one ounce bottle. This activator features also recommended for large gaps, low viscosity, solvent-free, suitable where prevailing temperatures are as low as less than+59 Degrees f (less than+15 Degrees c).

This PC 7257 repair and grouting system is grey and comes in a 10 pound bottle. This repair and grouting system features bonding to old and new concrete, bonds faster than concrete, no shrinkage, water free additive.

This PC 7257 repair and grouting system is grey and comes in a 10 pound bottle. This repair and grouting system features bonding to old and new concrete, bonds faster than concrete, no shrinkage, water free additive.

This PC 9599 wearing compound is blue in colour and comes in a 25 pound hobbock, pail. This wearing compound features fast cure, non- shrinking, non-sag.

This PC 9599 wearing compound is blue in colour and comes in a 25 pound hobbock, pail. This wearing compound features fast cure, non- shrinking, non-sag.

This SF 712 accelerator is clear and comes in a 0.7 fluid ounce aerosol can. It meets the standards for CFIA, MIL-A-46050C.

This SF 712 accelerator is clear and comes in a 0.7 fluid ounce aerosol can. It meets the standards for CFIA, MIL-A-46050C.

This SF 770 primer is clear and comes in a 1.75 fluid ounce bottle. It meets the standards for 49 CFR, NIOSH Approved, OSHA Hazard Communication Standard 29 CFR 1910.1200. This primer features improves adhesion of instant adhesives to polyolefins and other low surface energy plastics, tagliabue closed cup.

This SF 770 primer is clear and comes in a 1.75 fluid ounce bottle. It meets the standards for 49 CFR, NIOSH Approved, OSHA Hazard Communication Standard 29 CFR 1910.1200. This primer features improves adhesion of instant adhesives to polyolefins and other low surface energy plastics, tagliabue closed cup.

This SF 7649 primer and activator is green and comes in a 1.75 fluid ounce bottle. It meets the standards for ASTM D-5363, CFIA, MIL-S-22473E, NSF P1, NSF/ANSI 61. This primer and activator features for large bond gaps, for low-temperature curing ( less than 5 Degrees c), increases cure speed on passive and inactive surfaces.

This SF 7649 primer and activator is green and comes in a 1.75 fluid ounce bottle. It meets the standards for ASTM D-5363, CFIA, MIL-S-22473E, NSF P1, NSF/ANSI 61. This primer and activator features for large bond gaps, for low-temperature curing ( less than 5 Degrees c), increases cure speed on passive and inactive surfaces.

This SF 7471 activator is yellow and comes in a 4.5 ounce aerosol can. It meets the standards for ASTM D-5363 for New Designs, mil-S-2,2473E for Existing Designs. This activator features for large bond gaps, speeds up cure on passive and active surfaces.

This SF 7471 activator is yellow and comes in a 4.5 ounce aerosol can. It meets the standards for ASTM D-5363 for New Designs, mil-S-2,2473E for Existing Designs. This activator features for large bond gaps, speeds up cure on passive and active surfaces.

This SF 7387 activator is yellow and comes in a 4.5 fluid ounce aerosol can. It meets the standards for OSHA Hazard Communication Standard (29 CFR 1910.1200). This activator features speed up curing of most Loctite acrylic adhesives.

This SF 7387 activator is yellow and comes in a 4.5 fluid ounce aerosol can. It meets the standards for OSHA Hazard Communication Standard (29 CFR 1910.1200). This activator features speed up curing of most Loctite acrylic adhesives.

This SF 7452 accelerator is amber and comes in a 1.75 fluid ounce bottle. It meets the standards for 49 CFR, NIOSH Approved, OSHA Hazard Communication Standard 29 CFR 1910.1200. This accelerator features can be pre- or post-applied, cures excess adhesive, tagliabue closed cup.

This SF 7452 accelerator is amber and comes in a 1.75 fluid ounce bottle. It meets the standards for 49 CFR, NIOSH Approved, OSHA Hazard Communication Standard 29 CFR 1910.1200. This accelerator features can be pre- or post-applied, cures excess adhesive, tagliabue closed cup.