General Purpose Spiral-Point Taps

This tap is made of cobalt and has a 0.697 inch diameter, 3.1500 inch long shank. It is designed for use with cast iron, stainless steel, steel, and meets the standards for DIN/ASME. This PER-960SP series tap has a hard lube finish, and has fractional inch measurements. It has right hand direction with a 5.5118 inch length. Plus it has four flutes and a straight shank.

This tap is made of cobalt and has a 0.697 inch diameter, 3.1500 inch long shank. It is designed for use with cast iron, stainless steel, steel, and meets the standards for DIN/ASME. This PER-960SP series tap has a hard lube finish, and has fractional inch measurements. It has right hand direction with a 5.5118 inch length. Plus it has four flutes and a straight shank.

This tap is made of cobalt and has a 0.255 inch diameter, 1.8900 inch long shank. It is designed for use with cast iron, stainless steel, steel, and meets the standards for DIN/ASME. This PER-960SP series tap has a hard lube finish, and has fractional inch measurements. It has right hand direction with a 3.1496 inch length. Plus it has three flutes and a straight shank.

This tap is made of cobalt and has a 0.255 inch diameter, 1.8900 inch long shank. It is designed for use with cast iron, stainless steel, steel, and meets the standards for DIN/ASME. This PER-960SP series tap has a hard lube finish, and has fractional inch measurements. It has right hand direction with a 3.1496 inch length. Plus it has three flutes and a straight shank.

This tap spiral point ¼-20unc is made of high speed steel and has a 0.255 inch diameter, 1½ inch long shank. It is for use with steel, and meets the standards for Table 302A. This 1011-TC series tap spiral point ¼-20unc has a TiCN finish, and has fractional inch measurements. It has right hand direction with a 2½ inch length. Plus it has three flutes and a straight shank.

This tap spiral point ¼-20unc is made of high speed steel and has a 0.255 inch diameter, 1½ inch long shank. It is for use with steel, and meets the standards for Table 302A. This 1011-TC series tap spiral point ¼-20unc has a TiCN finish, and has fractional inch measurements. It has right hand direction with a 2½ inch length. Plus it has three flutes and a straight shank.

This tap spiral point m3x0.5 is made of high speed steel and has a 3.58mm diameter, 33.40mm long shank. It is designed for use with stainless steel/steel, and meets the standards for Table 302A. This 1011-TC series tap spiral point m3x0.5 has a TiCN finish, and has metric measurements. It has right hand direction with a 49.21mm length. Plus it has two flutes and a straight shank.

This tap spiral point m3x0.5 is made of high speed steel and has a 3.58mm diameter, 33.40mm long shank. It is designed for use with stainless steel/steel, and meets the standards for Table 302A. This 1011-TC series tap spiral point m3x0.5 has a TiCN finish, and has metric measurements. It has right hand direction with a 49.21mm length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 3/16 inch diameter, 4¾ inch long shank. It is for use with cast iron, steel, and meets the standards for USCTI TABLE 303A. This 1011E series spiral point tap has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction with a six-inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 3/16 inch diameter, 4¾ inch long shank. It is for use with cast iron, steel, and meets the standards for USCTI TABLE 303A. This 1011E series spiral point tap has a bright (uncoated) finish, and has fractional inch measurements. It has right hand direction with a six-inch length. Plus it has three flutes and a straight shank.

This spiral point hand tap is 17.46 millimetres long, with a M3.5 x 0.60 thread and a 3.58-millimetre shank diameter. This bright, right hand tap is made from high speed steel.

This spiral point hand tap is 17.46 millimetres long, with a M3.5 x 0.60 thread and a 3.58-millimetre shank diameter. This bright, right hand tap is made from high speed steel.

This hand tap is made of high speed steel and has a 0.194 inch diameter, 1½ inch long shank. It is designed for use with all materials, and meets the standards for USCTI. This 1011 series hand tap has a bright finish, and has pipe measurements. It has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This hand tap is made of high speed steel and has a 0.194 inch diameter, 1½ inch long shank. It is designed for use with all materials, and meets the standards for USCTI. This 1011 series hand tap has a bright finish, and has pipe measurements. It has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This low shear spiral point hand tap is 3 13/16 inches long, with a 5/8"-11 UNC thread and a 0.367-inch shank diameter. This right hand tap is made from high speed steel.

This low shear spiral point hand tap is 3 13/16 inches long, with a 5/8"-11 UNC thread and a 0.367-inch shank diameter. This right hand tap is made from high speed steel.

This tap is made of cobalt and has a 0.22 inch diameter, 2.0870 inch long shank. It is designed for use with cast iron, stainless steel, steel, and meets the standards for DIN/ASME. This PER-960SP series tap has a hard lube finish, and has pipe measurements. It has right hand direction with a 3.1496 inch length. Plus it has three flutes and a straight shank.

This tap is made of cobalt and has a 0.22 inch diameter, 2.0870 inch long shank. It is designed for use with cast iron, stainless steel, steel, and meets the standards for DIN/ASME. This PER-960SP series tap has a hard lube finish, and has pipe measurements. It has right hand direction with a 3.1496 inch length. Plus it has three flutes and a straight shank.

This spiral point hand tap is two inches long, with a #6-40 UNF thread and a 0.141-inch shank diameter. This right hand tap is made from high speed steel with a titanium carbo-nitride finish.

This spiral point hand tap is two inches long, with a #6-40 UNF thread and a 0.141-inch shank diameter. This right hand tap is made from high speed steel with a titanium carbo-nitride finish.

This spiral point hand tap is 3 5/32 inches long, with a 7/16"-14 UNC thread and a 0.323-inch shank diameter. This right hand tap is made from high speed steel with a titanium carbo-nitride finish.

This spiral point hand tap is 3 5/32 inches long, with a 7/16"-14 UNC thread and a 0.323-inch shank diameter. This right hand tap is made from high speed steel with a titanium carbo-nitride finish.

This spiral point hand tap is 4 1/4 inches long, with a 3/4"-10 UNC thread and a 0.59-inch shank diameter. This right hand tap is made from high speed steel with a titanium carbo-nitride finish.

This spiral point hand tap is 4 1/4 inches long, with a 3/4"-10 UNC thread and a 0.59-inch shank diameter. This right hand tap is made from high speed steel with a titanium carbo-nitride finish.

This spiral point bottoming hand tap is 1 15/16 inches long, with a #5-40 UNC thread and a 0.141-inch shank diameter. This right hand tap is made from high speed steel.

This spiral point bottoming hand tap is 1 15/16 inches long, with a #5-40 UNC thread and a 0.141-inch shank diameter. This right hand tap is made from high speed steel.

This low shear spiral point hand tap is two inches long, with a #6-32 UNC thread and a 0.141-inch shank diameter. This right hand tap is made from high speed steel.

This low shear spiral point hand tap is two inches long, with a #6-32 UNC thread and a 0.141-inch shank diameter. This right hand tap is made from high speed steel.

This tap is made of cobalt and has a 0.542 inch diameter, 70 mm long shank. It is designed for use with stainless steel/steel, and meets the standards for DIN/ASME. This PER-862SP series tap has a steam oxide finish, and has metric measurements. It has right hand direction with a 4.9213 inch length. Plus it has four flutes and a straight shank.

This tap is made of cobalt and has a 0.542 inch diameter, 70 mm long shank. It is designed for use with stainless steel/steel, and meets the standards for DIN/ASME. This PER-862SP series tap has a steam oxide finish, and has metric measurements. It has right hand direction with a 4.9213 inch length. Plus it has four flutes and a straight shank.

This hand tap is made of high speed steel and has a 0.318 inch diameter, 1.5950 inch long shank. It is designed for use with aluminum, brass, bronze, copper, and meets the standards for USCTI. This 1011-TN series hand tap has a TiN finish, and has fractional inch measurements. It has right hand direction with a 2-23/32 inch length. Plus it has two flutes and a straight shank.

This hand tap is made of high speed steel and has a 0.318 inch diameter, 1.5950 inch long shank. It is designed for use with aluminum, brass, bronze, copper, and meets the standards for USCTI. This 1011-TN series hand tap has a TiN finish, and has fractional inch measurements. It has right hand direction with a 2-23/32 inch length. Plus it has two flutes and a straight shank.